Identification
- Référence :
- QB09
- Intitulé :
- Sewerage
- Normes applicables :
- Non applicable
Caractéristiques certifiées
-
Sewerage-Drain-networks
- Vicat (> 79 ° C)
- Tensile strength (> 20MPa)
- Dimensional characteristics *
- Mechanical characteristics (ring stiffness min> 4kN / m2 *), creep <2.5)
- Impacts (TIR <10%)
- Heat reversion (<5%)
- Tightness of the assemblies of non-perforated tubes (No leaks according to standard NF EN 1053).
-
Small wastewater treatment systems
- Dimensional characteristics
- Mechanical characteristics in accordance with the requirements of the Technical Assessment
- Tightness
- “on site” purification performance (OBD, SS, OCD, NH4)
-
Rainwater treatment
- Dimensional characteristics
- Mechanical characteristics
- Tightness
-
Water storage device
- Surface weight
- Armor
- Thread
- Grip
- Tensile strength ( longitudinal direction / transverse direction)
- Elongation at break ( longitudinal direction / transverse direction)
- Resistance to tearing initiated ( longitudinal direction / transverse direction)
- Dimensional characteristics
- Tensile strength of welds
- Static Puncture resistance
- Resistance to chemical agents and UV
- Tightness of unperforated pipe assemblies.
-
Drain networks (peripheral drainage to buildings)
- Vicat> 75 ° C (if PVC)
- MFR and OIT if PP / PE
- Tests on the fiber coating (textile or geotextile)
- Mechanical resistance tensile, compression)
- Long-term mechanical behavior
- Dimensional characteristics
- Mechanical characteristics (ring stiffness, creep)
- Impact
- Static Puncture resistance
- Slot / perforation widths
-
Drain networks (drainage of road works)
- Vicat> 75 ° C (if PVC)
- MFR and OIT if PP / PE
- Tests on the fiber coating (textile or geotextile)
- Mechanical resistance (tensile, compression)
- Long-term mechanical behavior
- Dimensional characteristics
- Mechanical characteristics (ring stiffness, creep)
- Impact
- Slot / perforation widths
-
Storage of water and rainwater infiltration (boxes)
- MFR (if PP or PE)
- VICAT (if PVC)
- OIT (if PP or PE)
- Density
- Tensile
- Dimensional characteristics
- Determination of the resistance in simple compression (vertical direction) on a basic modulus
- Determination of the long-term compressive strength (vertical direction and horizontal direction)
-
Storage of water and rainwater infiltration (Thermoplastic tunnels)
- MFR
- OIT
- Density
- Tensile or flexion
- Creep
- Dimensional characteristics
- Determination of arch stiffness
-
Network rehabilitation
- Material characteristics
- Dimensional characteristics
- Short-term flexion
- Long-term flexion
- Tensile
-
Vacuum sewerage networks
- Tightness of the element and the assembly
-
Pipes, piping systems and accessories (Pipes made of thermoplastic materials)
- Internal pressure (pipes and fittings )
- OIT (if PP or PE) / Vicat (if PVC) / MFR (if PP or PE) (pipes and fittings )
- Tensile (Pipes)
- Density (Pipes)
- Ring flexibility (Pipes)
- Impact resistance (pipes and fittings)
- Ring stiffness (Pipes)
- Heat reversion (Pipes)
- Dimensional characteristics (pipes and fittings)
- Tightness (pipes and fittings)
- Creep ratio (Pipes)
- Quality of elastomer sealing rings (pipes and fittings)
- Mechanical resistance or flexibility of hand made fittings (Fittings)
-
Pipes, piping systems and accessories (GRP piping systems)
- Material characteristics
- Ring stiffness and initial tensile strength under flexing conditions
- Tightness
- Dimensional characteristics
-
Pipes, piping systems and accessories (Concrete pipes)
- Dimensional characteristics
- Mechanical resistance
- Tightness
-
Pipes, piping systems and accessories (Case of sleeves)
- Long-term shear strength
- Tightness
- Resistance to cycles at high temperatures (according to ATec requirements)
- Dimensional characteristics
-
Pipes, piping systems and accessories (Branching saddles)
- Vicat
- Density
- Internal pressure
- Flexibility
- Tightness
- Quality of elastomer sealing rings
- Dimensional characteristics
-
Pipes, piping systems and accessories (water meters)
- MFR
- Tensile
- Density
- weight
- Mechanical resistance of the cover
- Dimensional characteristics
Families
Documentation
| Date | Name | Type | Format |
|---|---|---|---|
| 2021-05-01 | Fascicule 70-1 - Fourniture, pose et réhabilitation de canalisations d'eaux à écoulement à surface libre | Other | |
| 2021-09-02 | Référentiel de certification QB09 rev11 | Referential | |
| 2021-09-02 | Annexe de gestion administrative de la certification QB09 rev11 | Referential | |
| 2021-09-02 | DT 99009-1-1 - Réseaux de drains | Other | |
| 2021-09-02 | DT 99009-1- 2 - Dispositifs d’assainissement non collectif | Other | |
| 2021-09-02 | DT 99009-1-3 - Traitement des eaux pluviales | Other | |
| 2021-09-02 | DT 99009-1-4 Dispositifs de stockage d’eau | Other | |
| 2021-09-02 | DT 99009-2-1 - Réseaux de drains | Other | |
| 2022-03-09 | DT 99009-2-2 - Tubes, canalisations et accessoires | Other | |
| 2021-09-02 | DT 99009-2-3 Système pour assainissement pluvial | Other | |
| 2021-09-02 | DT 99009-2-4 Réhabilitation de réseaux | Other | |
| 2021-09-02 | DT 99009-2-5 Réseaux d’assainissement sous vide | Other | |
| 2022-01-05 | Addendum applicable to all reference systems managed by CSTB | Referential |
Comité particulier
| Date | Name | Format |
|---|---|---|
| 2020-05-15 | Charte des membres de comités | |
| 2023-03-30 | Liste des membres du Comité QB 09 - Mars 2023 | |
| 2020-09-01 | Candidature pour un poste de membre de comité |
